Plate bevelers — cold beveling machines for plate and pipe to 4-3/4″

A plate bevelling machine prepares plate and pipe edges for welding: it sits on the edge, feeds itself along it and cuts the bevel cold — V, X, K or Y, at the angle and depth the weld procedure calls for — so there is no flame cut to clean, no heat-affected zone, no slag and no hours of grinding. NovoTech sells the bevellers of CEVISA, built in Vitoria, Spain, since 1969 and used by boiler and tank makers, structural fabricators, shipyards, wind-tower and offshore builders in more than 60 countries. On this page, small to large: the CHP 7, CHP 12 and CHP 12 INV standard shearing bevellers for plate, tube and discs from 1/8″ to 1-9/16″ thick; the CHP 12G, CHP 21G and CHP 21G INV with the bevel angle adjustable from 20° to 45°; the CHP 12G REV and CHP 21G REV that turn over to bevel the lower edge without turning the plate; and the CHP 30G, CHP 60G, CHP 60G INV and CHP 100G milling bevellers, which machine bevels up to 3-15/16″ wide at 15° to 70° in any material — Hardox, Armox, duplex and stainless included — on plate up to 4-3/4″. Supplied with a CSA-approved panel, installed and supported from Mississauga, ON, Canada. For chamfers on smaller parts, the NovoTech value-line CMD-80 and CMD-4 bench machines cut 15 – 45° chamfers up to 1/4″ and 5/32″, and the DM5 and DM5A hand units 3/16″ at 45°.

Plate beveller buying guideWhat to check before you buy

Cevisa bevellers are made in Vitoria, Spain, by CEVISA — plate bevelling machines since 1969, ISO 9001, exported to more than 60 countries; NovoTech's value-line chamfering machines are built in China to NovoTech's specification. All sold, installed and supported in Canada by NovoTech.

Specifications checked against the manufacturer's current catalogue · page updated

Cevisa Made in Spain

Cevisa shearing bevellers

Self-feeding bevellers that shear the bevel off cold with a resharpenable cutter, small to large: standard, adjustable-angle and reversible models for plate and tube from 1/8″ to 1-15/16″.

Made in Vitoria, Spain, since 1969 — Cevisa shearing and milling plate bevellers, sold, installed and supported in Canada by NovoTech.

CHP 7 · CHP 12 · CHP 12 INV standard shearing bevellers, bevel to 11/16″

CHP 7 · CHP 12 · CHP 12 INV · 3 models

The portable bevellers that do most of a fabrication shop's weld preparation: the machine sits on the plate edge, a shear cutter takes the bevel off cold in one or several runs, and the machine feeds itself along the edge — on the CHP 12 a 20 ft plate is bevelled in under three minutes. The 99 lb CHP 7 bevels plate, tube and aluminum from 1/8″ to 5/8″ thick to a 3/8″ bevel; the CHP 12, Cevisa's best-known machine since 1972, takes 1/4″ to 1-9/16″ plate to an 11/16″ bevel at 8.5 ft/min; the CHP 12 INV is the same machine working upside down on the lower edge, so an X bevel needs no plate turning. V, X, K and Y bevels at 22.5° to 45°; tube from Ø3-15/16″ inside, bevelled inside or out.

  • Self-feeding along the plate edge — no pushing and no supervision while it bevels
  • Cold shear cutting: no heat-affected zone, no slag, no grinding; cutters last about 3,300 ft (1,000 m) and are resharpened
  • V, X, K and Y bevels on plate, on tube from Ø3-15/16″ (100 mm) inside — inside or outside — and on discs from Ø13-3/4″ (350 mm)
  • Angle devices 22.5° – 45°; supplied with 3 cutters (1 on the machine), a 30° device, a tube device and spanners
  • On the bench, on casters or on a crane hook; reversing switch, thermal-magnetic trip and emergency stop
  • CHP 12 INV works upside down for lower bevels — under a CHP 12 it cuts the other half of an X bevel in the same pass
  • CSA-approved electrical panel; 600 V 3-phase with transformer (208 / 240 / 480 V on request)
CHP 7 · CHP 12 · CHP 12 INV Standard shearing bevellers
Model CHP 7CHP 12CHP 12 INV
Max. bevel length, mild steelone run / several runs 1/4″ / 3/8″ (6 / 10 mm)1/2″ / 11/16″ (12 / 18 mm)1/2″ / 11/16″ (12 / 18 mm)
Max. bevel length, stainlessone run / several runs 5/32″ / 5/16″ (4 / 8 mm)5/16″ / 5/8″ (8 / 16 mm)5/16″ / 5/8″ (8 / 16 mm)
Plate & tube thicknessnominal range 1/8″ – 5/8″ (3 – 16 mm)1/4″ – 1-9/16″ (6 – 40 mm)1/4″ – 1-9/16″ (6 – 40 mm)
Max. recommended thickness 5/16″ (8 mm)13/16″ (20 mm)13/16″ (20 mm)
Bevel angle 22.5° – 45° with angle devices22.5° – 45° with angle devices22.5° – 45° with angle devices
Bevel speed 5.2 ft/min (1.6 m/min)8.5 ft/min (2.6 m/min)8.5 ft/min (2.6 m/min)
Min. tube Øinside Ø3-15/16″ (100 mm)Ø3-15/16″ (100 mm)Ø3-15/16″ (100 mm)
Motor power 0.75 HP (0.55 kW)3 HP (2.2 kW)3 HP (2.2 kW)
Weight 99 lb (45 kg)143 lb (65 kg)143 lb (65 kg)

Bevel length is the width of the bevel face; its depth is the length × cos (bevel angle) — an 11/16″ bevel at 30° is about 5/8″ deep. Capacities for mild steel of 58 ksi (400 MPa) tensile strength; stainless steel as given. Metric values in brackets are the manufacturer's figures. Three-phase machines are supplied for 600 V; 208 V, 240 V or 480 V 3-phase available on request.

CHP 12G · CHP 21G · CHP 21G INV adjustable-angle bevellers, bevel to 1-1/8″

CHP 12G · CHP 21G · CHP 21G INV · 3 models

Adjustable-angle bevellers for production weld preparation: the bevel angle is set anywhere from 20° to 45° on the machine itself, and the trolley holds machine and plate in the best working position, which steadies the cut and lengthens cutter life. The CHP 12G is the adjustable CHP 12 — 1/4″ to 1-3/16″ plate, an 11/16″ bevel at 8.5 ft/min. The CHP 21G is built for round-the-clock work: 3/8″ to 1-15/16″ plate and a 1-1/8″ bevel in several runs (13/16″ in one) on a built-in trolley. The CHP 21G INV bevels the lower edge of heavy plate without turning it over, and side by side with a CHP 21G one operator bevels both edges.

  • Bevel angle adjustable from 20° to 45° on the machine — no angle devices to change
  • Self-feeding at 8.5 ft/min (CHP 12G) or 5.6 ft/min (CHP 21G); V, X, K and Y bevels on plate and tube
  • Trolley for a stable plate / machine position and longer cutter life — built in on the CHP 21G and 21G INV, working height 33-1/2″ – 34-5/8″ (850 – 880 mm)
  • CHP 21G: heavy-duty frame for 24-hour production; plates from 2-3/4″ (70 mm) wide
  • CHP 21G INV: lower bevels on heavy plate without turning it; works in pair with a CHP 21G
  • Electric box with reversing switch, thermal-magnetic trip and emergency stop; 3 cutters supplied (1 on the machine)
  • CSA-approved electrical panel; 600 V 3-phase with transformer (208 / 240 / 480 V on request)
CHP 12G · CHP 21G · CHP 21G INV Adjustable-angle shearing bevellers
Model CHP 12GCHP 21GCHP 21G INV
Max. bevel length, mild steelone run / several runs 1/2″ / 11/16″ (12 / 18 mm)13/16″ / 1-1/8″ (20 / 28 mm)13/16″ / 1-1/8″ (20 / 28 mm)
Max. bevel length, stainlessone run / several runs 5/16″ / 5/8″ (8 / 16 mm)1/2″ / 7/8″ (13 / 23 mm)1/2″ / 7/8″ (13 / 23 mm)
Plate & tube thicknessnominal range 1/4″ – 1-3/16″ (6 – 30 mm)3/8″ – 1-15/16″ (9 – 50 mm)3/8″ – 1-15/16″ (9 – 50 mm)
Max. recommended thickness 13/16″ (20 mm)1-9/16″ (40 mm)1-9/16″ (40 mm)
Bevel angle 20° – 45°, adjustable20° – 45°, adjustable20° – 45°, adjustable
Bevel speed 8.5 ft/min (2.6 m/min)5.6 ft/min (1.7 m/min)5.6 ft/min (1.7 m/min)
Min. tube Øinside Ø3-15/16″ (100 mm)Ø5-7/8″ (150 mm)Ø5-7/8″ (150 mm)
Motor power 3 HP (2.2 kW)4 HP (3 kW)4 HP (3 kW)
Weight 243 lb (110 kg)992 lb (450 kg)1,069 lb (485 kg)

Bevel length is the width of the bevel face; its depth is the length × cos (bevel angle) — an 11/16″ bevel at 30° is about 5/8″ deep. Capacities for mild steel of 58 ksi (400 MPa) tensile strength; stainless steel as given. Metric values in brackets are the manufacturer's figures. Three-phase machines are supplied for 600 V; 208 V, 240 V or 480 V 3-phase available on request.

CHP 12G REV · CHP 21G REV reversible bevellers, bevel to 1-1/8″

CHP 12G REV · CHP 21G REV · 2 models

Two bevellers in one: the head turns over on its frame in under a minute, so the same machine cuts the upper bevel and then the lower one without anyone turning the plate — X, K, V and Y bevels on large and heavy plate with one machine and one operator, and no crane work to flip the plate. The CHP 12G REV bevels 1/4″ to 1-3/16″ plate to an 11/16″ bevel at 8.5 ft/min; the CHP 21G REV combines a CHP 21G and a CHP 21G INV for 3/8″ to 1-15/16″ plate and a 1-1/8″ bevel. Bevel angle adjustable from 20° to 45° on both.

  • Turns over on its frame in under a minute for upper and lower bevels — the plate stays where it is
  • Bevel angle adjustable 20° – 45°; self-feeding; no supervision needed while it bevels
  • CHP 12G REV: 8.5 ft/min, 518 lb · CHP 21G REV: 5.6 ft/min, 1,385 lb, built-in trolley, working height 33-1/2″ – 34-5/8″
  • Plate and tube bevelling; electric box with reversing switch, thermal-magnetic trip and emergency stop
  • CSA-approved electrical panel; 600 V 3-phase with transformer (208 / 240 / 480 V on request)
CHP 12G REV · CHP 21G REV Reversible shearing bevellers
Model CHP 12G REVCHP 21G REV
Max. bevel length, mild steelone run / several runs 1/2″ / 11/16″ (12 / 18 mm)13/16″ / 1-1/8″ (20 / 28 mm)
Max. bevel length, stainlessone run / several runs 5/16″ / 5/8″ (8 / 16 mm)1/2″ / 7/8″ (13 / 23 mm)
Plate & tube thicknessnominal range 1/4″ – 1-3/16″ (6 – 30 mm)3/8″ – 1-15/16″ (9 – 50 mm)
Max. recommended thickness 13/16″ (20 mm)1-9/16″ (40 mm)
Bevel angle 20° – 45°, adjustable20° – 45°, adjustable
Bevel speed 8.5 ft/min (2.6 m/min)5.6 ft/min (1.7 m/min)
Min. tube Øinside Ø3-15/16″ (100 mm)Ø5-7/8″ (150 mm)
Motor power 3 HP (2.2 kW)4 HP (3 kW)
Weight 518 lb (235 kg)1,385 lb (628 kg)

Bevel length is the width of the bevel face; its depth is the length × cos (bevel angle) — an 11/16″ bevel at 30° is about 5/8″ deep. Capacities for mild steel of 58 ksi (400 MPa) tensile strength; stainless steel as given. Metric values in brackets are the manufacturer's figures. Three-phase machines are supplied for 600 V; 208 V, 240 V or 480 V 3-phase available on request.

Cevisa Made in Spain

Cevisa milling bevellers

Portable milling machines that machine the bevel with an insert head — any material, 15° to 70°, transition and J bevels, on plate to 4-3/4″.

Made in Vitoria, Spain, since 1969 — Cevisa shearing and milling plate bevellers, sold, installed and supported in Canada by NovoTech.

CHP 30G · CHP 60G · CHP 60G INV · CHP 100G milling bevellers, bevel to 3-15/16″

CHP 30G · CHP 60G · CHP 60G INV · CHP 100G · 4 models

Portable milling machines that bevel: an insert milling head machines the bevel while feed rollers carry the machine along the plate and pneumatic clamps hold it down — a machined face with no heat and no grinding, in any material from mild steel to Hardox and duplex at the same capacity, at 15° to 70°, with transition and J bevels. CHP 30G: plate 1/8″ – 1-15/16″, bevel to 1-3/8″. CHP 60G: plate 3/8″ – 2-3/4″ (3-15/16″ in special configuration), bevel to 2-3/8″, and the CHP 60G INV for lower bevels. CHP 100G: plate to 4-3/4″, bevel to 3-15/16″.

  • Machined bevel face from an insert milling head — no grinding before welding and no change to the steel
  • The same capacity in every material: mild and stainless steel, Hardox, Armox, duplex, super duplex, aluminum
  • Bevel angle 15° – 70°; electronic display of bevel width; adjustable feed and spindle speed
  • V, X, K, Y, transition (slope) and slope + bevel; J bevels with the J-bevel device (CHP 60G)
  • Pneumatic clamping and feed rollers for a vibration-free cut; shop air 7 CFM (200 l/min)
  • Built-in trolley; pneumatic working height 29-7/8″ – 37″ (CHP 60G); control pendant; chip drawer
  • CHP 60G INV bevels the lower edge and works in parallel with a CHP 60G
  • CSA-approved electrical panel; 600 V 3-phase with transformer (208 / 240 / 480 V on request)
CHP 30G · CHP 60G · CHP 60G INV · CHP 100G Milling bevellers
Model CHP 30GCHP 60GCHP 60G INVCHP 100G
Max. bevel length, any materialone run / several runs 1″ / 1-3/8″ (25 / 35 mm)1-9/16″ / 2-3/8″ (40 / 60 mm)1-9/16″ / 2-3/8″ (40 / 60 mm)3-7/16″ / 3-15/16″ (88 / 100 mm)
Plate thicknessnominal range 1/8″ – 1-15/16″ (3 – 50 mm)3/8″ – 2-3/4″ (10 – 70 mm) · to 3-15/16″ (100 mm) in special configuration3/8″ – 2-3/4″ (10 – 70 mm) · to 3-15/16″ (100 mm) in special configuration3/8″ – 4-3/4″ (10 – 120 mm)
Max. recommended thickness 1-15/16″ (50 mm)2-3/4″ (70 mm)2-3/4″ (70 mm)4-3/4″ (120 mm)
Bevel angle 15° – 70°, adjustable15° – 70°, adjustable15° – 70°, adjustable15° – 70°, adjustable
Bevel speed 31.5 in/min (800 mm/min)26.4 in/min (670 mm/min)26.4 in/min (670 mm/min)21.7 in/min (550 mm/min)
Motor power 3 HP (2.2 kW)5 HP (3.8 kW)5 HP (3.8 kW)15 HP (11 kW)
Weight 1,367 lb (620 kg)1,786 lb (810 kg)1,786 lb (810 kg)8,047 lb (3,650 kg)

Bevel length is the width of the bevel face; the milling bevellers have the same capacity in every material, from mild steel to Hardox. Metric values in brackets are the manufacturer's figures. Three-phase machines are supplied for 600 V; 208 V, 240 V or 480 V 3-phase available on request.

NovoTech Value line

Edge chamfering machines · value line

Bench chamfering machines and hand chamfering units for weld preps and clean edges on plate, strip and parts — NovoTech value line, built in China.

NovoTech's own brand: manufactured in China to high North American quality standards, with the same CSA-approved panel, 1-year warranty and parts and support in Canada as every machine we sell

CMD-4 · CMD-80 edge chamfering machines and DM5 hand chamfering tools

CMD-4 – DM5A · 4 models

Edge chamfering machines that put a 15 – 45° weld prep or a clean deburred edge on plate, strip and parts: the CMD-80 cuts chamfers up to 1/4″ (6 mm) from 1.5 HP, the CMD-4 up to 5/32″, and the compact DM5 units 3/16″ at 45°.

  • CMD-80: chamfers 0 – 1/4″ (6 mm) at 15 – 45°, 1.5 HP
  • CMD-4: chamfers 0 – 5/32″ (4 mm) at 15 – 45°
  • DM5 / DM5A: compact units, 45° chamfers to 3/16″ (5 mm), 20 lb
CMD-4 · CMD-80 · DM5 · DM5A Edge chamfering machines for 15 – 45° weld preps and deburring
Model CMD-4CMD-80DM5DM5A
Chamfer size 0 – 5/32″ (0 – 4 mm)0 – 1/4″ (0 – 6 mm)0 – 3/16″ (0 – 5 mm)0 – 3/16″ (0 – 5 mm)
Chamfer angle 15 – 45°15 – 45°45°45°
Motor 1/2 HP (0.375 kW)1.5 HP (1.1 kW)1/2 HP (370 W)1/3 HP (250 W)
Motor speed 2,800 rpm2,800 rpm0 – 4,300 rpm2,800 rpm
Packing size L × W × H 22 × 16 × 19″ (56 × 40 × 48 cm)23 × 19 × 23″ (59 × 48 × 58 cm)13 × 13 × 9″ (34 × 34 × 23 cm)13 × 13 × 9″ (34 × 34 × 23 cm)
Weight 62 lb (28 kg)146 lb (66 kg)20 lb (9 kg)20 lb (9 kg)

Metric values in brackets are the manufacturer's figures; thin sheet is given in gauge. Packing size is the shipping crate L × W × H and weight is the net weight of the machine. Three-phase machines are supplied for 600 V; 208 V, 240 V or 480 V 3-phase available on request.

Included with every machine from NovoTech

  • CSA-approved electrical panelEvery machine ships with a CSA-approved panel, wired for Canadian voltage.
  • Parts and support in CanadaSpare parts and technical support readily available from Mississauga, ON, Canada.
  • 7-day money-back guaranteeTry the machine in your shop — full refund within 7 days on in-stock models.
  • 1-year warrantyOn every new machine we sell, with parts and service from Mississauga, ON, Canada.
  • Made in Spain by CevisaCEVISA has built self-feeding plate and tube bevellers in Vitoria, Spain, since 1969 — patented shearing and milling bevellers, an ISO 9001 quality system and 80 % of production exported to more than 60 countries.
  • Installation and trainingOur technicians commission the machine and train your operators, anywhere in Canada — on request, at an additional charge.
  • Remote troubleshooting by video callOur technicians diagnose faults and guide your operator through the fix over a video call.
  • Shipping across Canada and the US from OntarioFrom our warehouse in Mississauga, Ontario, Canada, we deliver to every province and territory and export to customers anywhere in the United States — freight arranged by NovoTech at competitive rates.
  • Financing with 0% downLease or finance the machine with 0% down and competitive rates through our financing partners — keep your cash working in the shop.
  • Order today with 10% downSimple payment terms: 10% down payment to place your order, the remaining 90% before shipping from our warehouse in Mississauga, ON, Canada.
  • 5% off your second machineReturning customers get 5% off their next machine from NovoTech — our thank-you for coming back.

Three-phase machines are supplied for 600 V; 208 V, 240 V or 480 V 3-phase available on request.

Inside the factory — Cevisa in Vitoria, Spain

A tour of the Cevisa plant in Vitoria, where the shearing and milling bevellers on this page are designed and built. More videos are on NovoTech's YouTube playlist.

Cevisa bevelling machines — factory introduction

Cevisa bevelling machines — factory introduction

Plate beveller buying guide

What we explain to customers before they buy a plate bevelling machine: why bevel cold, shearing or milling bevellers, how to size the machine by the bevel face, bevelling both sides, pipe and discs, and running costs. Written by NovoTech's sales engineers and technicians from years of installing machines in Canada.

Why bevel cold?

A full-penetration weld on plate or pipe needs a prepared edge: a V, X, K, Y or J bevel at the angle and depth the weld procedure gives. Bevels of 30°, 37.5° and 45° are common, often with a small flat land (root face) left at the bottom. Cut with a torch, the bevel leaves slag, scale and a heat-affected zone, and ground by hand it takes hours and never comes out even. A plate bevelling machine sits on the edge of the plate, feeds itself along it and cuts the bevel cold. It is clean, even and ready to weld, at several feet a minute, with one operator who does not have to hold or guide it. Boiler and tank makers, structural fabricators, shipyards, and wind-tower and offshore builders use them for exactly that reason.

Cevisa CHP 12 plate and tube bevelling machine

Shearing or milling beveller?

A shearing beveller takes the bevel off with a resharpenable shear cutter, in a curled chip. It gives the fastest and lowest-cost bevel per foot in mild steel, stainless and aluminum, on plate and on pipe, and the cutters last about 3,300 ft of bevel before resharpening.

A milling beveller machines the bevel with a milling head of indexable inserts. It gives a machined finish in any material, including wear plate, armour plate, duplex and super duplex stainless. It cuts any angle from 15° to 70°, transition and J bevels, and very wide bevels on thick plate.

For mild steel and stainless in everyday weld preparation, the shearing machine is the economical choice. For hard and exotic materials, J bevels or very thick plate, choose the milling machine.

Cevisa CHP 60G milling beveller with pneumatic height adjustment and built-in trolley

How to size a beveller

Bevellers are rated by the width of the bevel face they cut and by the plate thickness range, not by the plate thickness alone. A steep or deep bevel on thick plate has a wide face and may need a larger machine than the thickness suggests. Start from your largest joint: its plate thickness, bevel angle and root face. In stainless, a shearing machine cuts about 80 – 90 % of its mild-steel bevel in several passes and about two-thirds in one pass, while milling machines keep their full capacity. Send us the joint detail from your weld procedure and we will check it against each machine.

Both sides, pipe and discs

X and K joints need a bevel on both the top and bottom edge. Turning a heavy plate over takes a crane and time, so there are two better ways:

  • An inverted (INV) machine bevels the lower edge from underneath, and run together with its standard twin it cuts both bevels in one pass.
  • A reversible (REV) machine turns over on its frame in under a minute and does both bevels by itself.

The shearing machines also bevel tube and pipe, on the inside or the outside, with the pipe horizontal or vertical, as well as discs and tank heads. Milling bevellers are for plate and bar.

CHP 21G REV turned over on its frame to bevel the lower edge

Small parts and light chamfers

A plate beveller travels along plate and pipe. For a chamfer or a deburred edge on small parts and strip, a bench chamfering machine is quicker to set up: the part slides along a fence past a cutter set to the angle. The value-line CMD-80 cuts chamfers up to 1/4″ at 15 – 45° and the CMD-4 up to 5/32″, and the DM5 and DM5A hand units cut 3/16″ at 45° on parts too large to lift onto a bench.

CMD-80 edge chamfering machine for 15 – 45° weld preps

Running costs, power and set-up

Bevellers cost little to run: the shearing cutters are resharpened, and the milling heads use standard inserts. The machines need little maintenance, and a 20 ft plate edge is bevelled in a few minutes. Plan how the plate will be supported at a comfortable height, on a table or trestles with room for the machine to travel the full edge, and how chips will be collected. The bevellers run on 600 V three-phase with a CSA-approved panel (208, 240 or 480 V on request). We quote the cutters, inserts and angle devices with the machine, and train your operators at delivery.

Questions we get asked about plate bevelling machines

What does a plate bevelling machine do?

It cuts the bevel a full-penetration weld needs on the edge of a plate or pipe — V, X, K or Y, at a set angle and depth — and feeds itself along the edge while it cuts. Compared with a cutting torch and a grinder it leaves a clean, even bevel with no heat-affected zone, no slag and no scale to grind off, ready to weld, and it does it at several feet a minute with one operator who does not have to hold or guide it.

Shearing or milling beveller?

A shearing beveller (CHP 7 to CHP 21G) takes the bevel off with a resharpenable shear cutter: the fastest and lowest-cost bevel per foot in mild steel, stainless and aluminum, on plate and tube up to 1-15/16″ and bevels up to 1-1/8″. A milling beveller (CHP 30G, 60G, 100G) machines the bevel with a milling head: a machined finish in any material — Hardox, Armox, duplex, super duplex — at the same capacity, angles from 15° to 70°, transition and J bevels, and bevels up to 3-15/16″ wide on plate to 4-3/4″.

Which size do I need?

Start from the widest bevel face and the thickest plate you prepare. CHP 7: bevels to 3/8″ on 1/8″ – 5/8″ plate and thin tube, also aluminum. CHP 12 / 12G: 11/16″ bevels on 1/4″ to 1-9/16″ (12G 1-3/16″). CHP 21G: 1-1/8″ bevels on 3/8″ – 1-15/16″ plate, for continuous production. CHP 30G: 1-3/8″ machined bevels to 1-15/16″ plate; CHP 60G: 2-3/8″ on plate to 2-3/4″ (3-15/16″ special); CHP 100G: 3-15/16″ on plate to 4-3/4″. In stainless steel the shearing machines take 80 – 90 % of their mild-steel bevel in several runs and about two-thirds in one run; the milling machines keep their full capacity.

What do INV and REV mean?

An INV (inverted) machine works upside down and bevels the lower edge of the plate, so the lower half of an X or K bevel is cut without turning a heavy plate over; running an INV under its standard twin (CHP 12 + 12 INV, 21G + 21G INV, 60G + 60G INV) cuts both bevels in one pass. A REV (reversible) machine turns over on its frame in under a minute and does both bevels by itself — one machine, one operator.

Can it bevel pipe and discs?

Yes, the shearing models bevel tube and pipe as well as plate: from Ø3-15/16″ inside (Ø5-7/8″ on the CHP 21G family), on the inside or the outside, with the pipe horizontal or vertical, and discs and tank heads from Ø13-3/4″. The milling bevellers are for plate, flat bar and square bar.

What does it cost to run?

Little: the shearing cutters last about 3,300 ft (1,000 m) of bevel and are resharpened, Cevisa rates the machines maintenance-free, and a 20 ft plate edge is bevelled in under three minutes on a CHP 12. The milling heads use standard indexable inserts. We quote cutters, inserts and angle devices with the machine.

What voltage do these machines run on?

Three-phase machines are supplied for 600 V as standard with a CSA-approved panel; 208 V, 240 V and 480 V 3-phase are available on request, and 240 V single-phase on models whose main motor is 2.2 kW (3 HP) or less — a machine with a motor above 2.2 kW must run on three-phase power and cannot be converted to 240 V single-phase. Manual machines have no electrics.

Request a quote

Tell us which machine you are looking at and what you will run on it — material, sizes and voltage — and we will come back with pricing, delivery and the right options for your shop. We answer within one business day.

Prefer to talk? Call +1 647 526 5510 (Mon–Fri 9:00–17:00 Eastern) or email infoNovoTechMachineTools.com.

1365 Mid-Way Blvd, Unit 26, Mississauga, ON L5T 2J5, Canada

Your quote requestWe reply within one business day

Part drawings or sketches, photos of your parts — PDF, DWG, DXF, STEP, IGES, JPG, PNG, ZIP, Excel or Word · up to 10 files, 13 MB in total.

This form is protected by reCAPTCHA; Google's Privacy Policy and Terms of Service apply.

Represent NovoTech in your city or province

Sales agents wanted across Canada

NovoTech is appointing independent sales agents and dealers in cities and provinces across Canada — British Columbia, Alberta, Saskatchewan, Manitoba, Ontario outside the GTA, Quebec and Atlantic Canada. If you already call on steel fabricators, rebar shops, precast plants, HVAC shops or contractors, add a proven line of GMS, Dener and other metalworking machinery to what you offer.

  • Open to individuals and companies with customers in metal fabrication or construction
  • Quotations, brochures, videos and demonstrations prepared by NovoTech for your customers
  • Installation, operator training, spare parts and technical support stay with NovoTech in Mississauga, ON, Canada
Apply to become an agent Call +1 647 526 5510

Tell us your territory and the customers you serve — we reply within one business day.